Question
Which combinations of Automation Engine and Grapholas are supported ?
Answer
This page contains compatibility information between Automation Engine and iPC
"Submit to Flexo CTP Device"/"Create Merged Plate" Task
Following chart lists compatibility of the "Submit Flexo CTP Device" task with Grapholas.
Note : The task "Submit to Flexo CTP Device" was called Submit to CDI Device in Automation Engine 18.1.0 and below.
| Grapholas Version | |||||||||||||||||
| 23.03 | 22.11 | 22.7 | 22.3 | 20.1 | 20.0 | 19.1 | 19.0 | 18.2 | 18.1 | 18.0 | 16.1 | 16.0 | 14.1 | 14.0 | 12.1 | ||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Automation Engine Version | 23.07 |  | | | | | | | | | | | | | | |  |
| 23.03 | | | | | | | | | | | | | | | | | |
| 22.11 | | | | | | | | | | | | | | | 1) | | |
| 22.07 | | | | | | | | | | | | | | | 1) | 1) | |
| 22.03 | | | | | | | | | | | | | | | 1) | 1) | |
| 21.11 | | | | | | | | | | | | | | | 1) | 1) | |
| 21.07 | | | | | | | | | | | | | | | 1) | 1) | |
| 21.03 | | | | | | | | | | | | | | | 1) | 1) | |
| 20.1.0 | | | | | | | | | | | | | | | 1) | 1) | |
20.0.0 | | | | | | 2) | | | | | | |
| |
|
| |
18.1.1 | | | | | | | |
| | | | |
|
|
|
| |
18.1.0 | | | | | | | | | | | | |
|
|
|
| |
18.0.1 | | | | | | | | | | | | |
|
|
|
| |
18.0.0 | | | | | | | | | | | | |
|
|
|
| |
16.1.1 | | | | | | | | | | | | |
|
|
|
| |
16.1.0 | | | | | | | | | | | | |
|
|
|
| |
16.0.2 | | | | | | | | | | | | |
|
| | | |
Notes
1. - Supported with some limitations ( f.e. inaccurate time estimation )
2. - Not recommended, strongly advised to upgrade to a fully compatible version
: Not tested
Note about LENX
If working with LENX, files : In Automation/Imaging Engine 18.0.0, make sure you have Grapholas/DFS 18.0 or higher, in Automation/Imaging Engine 18.0.1, make sure you have Grapholas/DFS 18.1 or higher. So, if you are working with LENX in Automation Engine 18.0.0 and are planning to upgrade to 18.0.1 or higher, make sure you have at least Grapholas 18.1.
| Version of Automation Engine | Integrated version of Digital Flexo Suite/PlatePrep |
|---|---|
| Automation Engine 23.07 | 23.3.1 |
| Automation Engine 23.03 | 22.11.9 |
| Automation Engine 22.11 | 22.7.1 |
| Automation Engine 22.07 | 22.3.5 |
| Automation Engine 22.03 | 20.1.12 |
| Automation Engine 21.11 | 20.0.18 |
| Automation Engine 21.07 | 20.0.17 |
| Automation Engine 21.03 | 20.0.6 |
| Automation Engine 20.1.0 | 20.0.6 |
| Automation Engine 20.0.0 | 19.1.9 |
| Automation Engine 18.1.1 | 19.0.7 |
| Automation Engine 18.1.0 | 18.1.1 |
| Automation Engine 18.0.1 | 18.0.1 |
| Automation Engine 18.0.0 | 18.0.0 |
| Automation Engine 16.1.1 | 16.1.0 |
| Automation Engine 16.1.0 | 16.1.0 |
| Automation Engine 16.0.2 | 16.0.4 |
| Article information | |
|---|---|
| Applies to | Automation Engine 16.0.2 and above Grapholas 12.1 and above |
| Created |
|
| Last revised |
|
| Author | |
| Case Number | |